How to choose speaker drivers for a custom build
A custom speaker starts with the drivers: the tweeters, midranges, woofers and subwoofers that actually make the sound. Choose them well and the box can be built to get the best from them. Here is how to pick drivers for your room, your amplifier and your budget, without getting lost in spec sheets.
What a driver does
Each driver covers part of the sound. No single driver plays everything well, so a speaker splits the work:
- Tweeter (usually 1 inch): the high notes, such as cymbals, the "s" in voices and the air around instruments.
- Midrange (around 5 to 5.25 inch in a tower): voices and most instruments. This is where your ears are most sensitive.
- Woofer (5 to 6.5 inch in home speakers): the lower notes, such as bass guitar, drums and the body of a piano.
- Subwoofer (8, 10 or 12 inch): the deepest bass you feel as much as hear, in films and music.
A crossover sends each driver only the notes it is good at. In a passive speaker it sits inside the box; in an active or DSP system it is set in the amplifier.
1. Decide 2-way or 3-way
| Design | Drivers | Suits | Our enclosure |
|---|---|---|---|
| 2-way bookshelf | 1" tweeter + 5–5.25" woofer | Bedrooms, studies, desks and smaller living rooms | ES-B2, ₹9,000 a pair |
| 3-way tower | 1" tweeter, 5–5.25" midrange, 2 × 6.5" woofers | Bigger living rooms and fuller sound without a subwoofer | ES-T3, ₹11,000 single, ₹18,000 a pair |
| Subwoofer | One 8", 10" or 12" driver | Adding deep bass to either | ES-S, ₹7,000 · ₹15,000 · ₹25,000 |
A 2-way speaker is simpler and easier to get right on a modest budget. A 3-way lets the woofers handle bass while a separate midrange keeps voices clean, so it can play bigger rooms with less strain. Not sure which? Our bookshelf vs tower guide compares them by room size.
2. Pick sizes for your room
Bigger woofers move more air, which means more bass and more volume, but they also need a bigger box. As a rough guide, a 5 to 5.25-inch woofer suits a smaller room or near-field listening, and a pair of 6.5-inch woofers suits a larger living room. For the deepest bass, add a subwoofer sized for the room: 8 or 10 inch up to 150 sq ft, 10 or 12 inch for 150 to 300 sq ft, and a 12 inch or two subwoofers above that. See how to add a subwoofer.
3. Read the spec sheet: four numbers that matter
- Sensitivity (dB at 1 W / 1 m): how loud a driver plays for a given power. A few dB higher means noticeably louder from the same amplifier. In a multi-way speaker, the drivers should be close in sensitivity, or the crossover has to turn the louder one down.
- Impedance (usually 4 or 8 ohms): check it suits your amplifier or AV receiver. Many receivers prefer 8-ohm speakers.
- Power handling (RMS): the steady power the driver can take. Ignore large "peak" or "max" figures. An amplifier with a little more clean power than you need is safer than a small one pushed into distortion.
- Frequency range: useful to see where each driver is comfortable, so the crossover can hand over in the right place.
Woofer and subwoofer data sheets also list Thiele/Small parameters (such as Fs, Qts and Vas). You do not need to understand them: they are what we use to work out the box volume, the port and whether a driver suits a sealed or ported box.
4. Match the drivers to the box, not the other way round
The same driver can sound thin in one box and full in another. That is why we build each enclosure by hand around the drivers you choose: the internal volume, bracing, damping and port are matched to them, and the front is routed so they sit flush. For subwoofers we can go further and build a tuned-dimension box sized for your exact driver after measuring it; that is quoted once we have the driver.
Two practical tips: choose drivers from one range where you can, as they are designed to work together; and buy matched pairs, so left and right sound the same.
5. Plan the amplifier with the drivers
- Passive speakers need an amplifier or AV receiver. Our power amplifiers come in 2, 4 and 5 channels at 80, 100 or 120 W per channel.
- Built-in amplifier: our bookshelf pair and towers can have one built in, so you plug in a TV, phone or streamer directly. It adds ₹3,000 for the bookshelf pair and ₹5,000 per tower.
- DSP amplifier: sets the crossover, EQ, delay and level for every driver and corrects room problems. See our DSP amplifiers.
6. Spend where you hear it
- Put the most money into the drivers that play voices: the midrange or the 2-way woofer, and a good tweeter.
- A well-built box often does more for sound than a more expensive driver in a poor one.
- If films and music feel thin, a subwoofer usually helps more than bigger main drivers.
- Leave room in the budget for an amplifier with enough clean power.
Common mistakes
- Choosing drivers by peak watts or the biggest magnet.
- Mixing a very loud tweeter with a quiet woofer and no crossover to balance them.
- Fitting a woofer into whatever box is to hand, too small or too large for it.
- Forgetting impedance, then finding the receiver runs hot or shuts down.
Let us choose with you
You can bring drivers from your favourite brand, or tell us your room, your music and your budget and we recommend drivers to match. Either way, we build the enclosure around them in our Delhi NCR workshop, then install and tune the system in your space. Prices are in our custom speaker box price guide; for a whole system, see a custom system.
Questions
Which speaker drivers should I buy for a custom build?
Start from your room and how you listen. A 2-way pair (1-inch tweeter and 5 to 5.25-inch woofer) suits smaller rooms; a 3-way tower with 2 × 6.5-inch woofers suits bigger rooms. Add a subwoofer for deep bass.
Does the speaker box matter as much as the drivers?
Yes. The volume, bracing, damping and port of the box decide how a driver sounds, especially in the bass. That is why we build each enclosure around the drivers you choose.
What do sensitivity and impedance mean?
Sensitivity is how loud a driver plays for a given power, in dB at 1 W and 1 m. Impedance, usually 4 or 8 ohms, must suit your amplifier or AV receiver.
Can I use drivers I already bought?
Yes. Send us the make and model and we build the enclosure for them. For subwoofers we can build a tuned-dimension box after measuring your driver.
Do you sell the drivers?
Speakers are priced separately in your quote. You can choose your favourite brand, or ask us to recommend drivers for your budget.
How much does the enclosure cost?
Our ES-B2 bookshelf pair is ₹9,000, the ES-T3 tower ₹11,000 single or ₹18,000 a pair, and ES-S subwoofer boxes ₹7,000, ₹15,000 or ₹25,000. Drivers are extra.
Not sure which drivers?
Tell us your room, your music and your budget. We suggest drivers, build the box around them and give you a fixed price on WhatsApp.